This page covers the hardware reference. For the philosophy and the right-to-repair context behind it, see the Open Source Overview.
Every layer of the Defend-O-Tron’s software is open source: the Linux kernel, the Debian operating system, the system services, the defense components (CrowdSec, Suricata, AdGuard Home), the web proxy (Traefik) and the metrics store (VictoriaMetrics). If you want to audit it, you can.
The V100’s chip also has a 0.8 TOPS NPU. The Defend-O-Tron firmware does not use it.
The V200’s hardware design is not open source, but its firmware is. Instead of a closed BIOS, it runs Dasharo, an open-source firmware distribution. On the V200 it is coreboot with a UEFI interface. See Defend-O-Tron V200.
The rest of this page is about the V100.
The V100 is built on the FriendlyElec NanoPi R5S board. Its schematic:
PCB: 8 Layer, 62x90x1.6mm


| Pin # | GPIO | SPI | UART | PWM | POWER | Description |
|---|---|---|---|---|---|---|
| 1 | VCC3V3_SYS | 3.3v | power output | |||
| 2 | VCC3V3_SYS | 3.3V | power output | |||
| 3 | GPIO3_C3 | SPI1_CLK_M1 | UART5_RX_M1 | 3.3V | level | |
| 4 | GND | |||||
| 5 | GPIO3_C2 | SPI1_MISOI_M1 | UART5_TX_M1 | 3.3V | level | |
| 6 | GPIO3_A1 | SPI1_CS0_M1 | 3.3V | level | ||
| 7 | GPIO3_C1 | SPI1_MOSI_M1 | 3.3V | level | ||
| 8 | GND | |||||
| 9 | GPIO4_C5 | UART9_TX_M1 | PWM12_M1 | 3.3V | level | |
| 10 | GPIO4_C6 | UART9_RX_M1 | PWM13_M1 | 3.3V | level | |
| 11 | GPIO3_C4 | UART7_TX_M1 | PWM14_M0 | 3.3V | level | |
| 12 | GPIO3_C5 | UART7_RX_M1 | PWM15_IR_M0 | 3.3V | level | |
| Pin # | PIO | SD/MMC/SDIO | I2S | POWER | Description |
|---|---|---|---|---|---|
| 1 | VCC5V0_SYS | 5V | power output | ||
| 2 | VCC5V0_SYS | 5V | power output | ||
| 3 | GPIO3_C6 | SDMMC2_D0_M0 | I2S1_MCLK_M1 | 1.8V | level |
| 4 | GPIO3_C7 | SDMMC2_D1_M0 | I2S1_SCLK_TX_M1 | 1.8V | level |
| 5 | GND | ||||
| 6 | GND | ||||
| 7 | GPIO3_D0 | SDMMC2_D2_M0 | I2S1_LRCK_TX_M1 | 1.8V | level |
| 8 | GPIO3_D3 | SDMMC2_CLK_M0 | I2S1_SDI1_M1 | 1.8V | level |
| 9 | GND | ||||
| 10 | GND | ||||
| 11 | GPIO3_D1 | SDMMC2_D3_M0 | I2S1_SDO0_M1 | 1.8V | level |
| 12 | GPIO3_D2 | SDMMC2_CMD_M0 | I2S1_SDI0_M1 | 1.8V | level |
| 13 | GND | ||||
| 14 | GND | ||||
| 15 | GPIO3_D5 | SDMMC2_PWREN_M0 | I2S1_SDI3_M1 | 1.8V | level |
| 16 | GPIO3_D4 | SDMMC2_DET_M0 | I2S1_SDI2_M1 | 1.8V | level |
| Pin # | Assignment | Description |
|---|---|---|
| 1 | GND | 0V |
| 2 | UART2DBG_TX | output |
| 3 | UART2DBG_RX | input |
USB Port
Each USB 3.2 Gen 1 port has 1.4A overcurrent protection.
RTC
RTC backup current is 0.25μA TYP (VDD =3.0V, TA =25℃).
Connector P/N: Molex 53398-0271